Authors:
K. Arunkarthikeyan,A. Chinnamahammad Bhasha,M. Venkata pavan, P.Sneha, Shaik. Abrar,DOI NO:
https://doi.org/10.26782/jmcms.2020.07.00039Keywords:
AWJM,Turning,Chuck and motor assembly,Worktable design,Abstract
Abrasive water jet had proven to be a suitable unconventional machine technique for cut-through operation. Using abrasive water jet turning only limited studies are available. Apart from usual machining practice in Abrasive Water Jet Machine (AWJM), the installation of the chuck with motor assembly as a unit similar set up like conventional lathe machine will enhance the machinability of AWJM. From the earlier studies, it is understood that the author has performed the machinability studies using this experimental set up in AWJM. But no standard procedure is described as the installation procedure of chuck and motor assembly in AWJM. Considering this, a review is conducted on the design and implementation of turning setup in an abrasive water jet machine. Based on the acquired knowledge through a literature survey and also, considering vibration, assembly, and safety factors, a new design is proposed. The author ensures that implementing this setup in an abrasive water jet machine will enhance the research work to a higher level of significance.Refference:
I. R. Rakshit, A.K. Das, “A review on cutting of industrial ceramic materials” Precision Engineering, Vol:59, Pages : 90-09, 2019
II. P. Ranjan, S.S. Hiremath,”Role of textured tool in improving machining performance: a review”, Journal of Manufacturing Processes, Vol:43,Pages : 47-73, 2019
III. A.I. Ansari, M. Hashish, M.M. Ohadi, “Flow visualization study of the macromechanics of abrasive-waterjet turning”, Experimental Mechanics, Vol:32, Pages : 358-364, 1992
IV. I Zohourkari, M. Zohoo, M. Annoni,“Investigation of the effects of machining parameters on material removal rate in abrasive waterjet turning”, Advances in Mechanical Engineering, Vol:6, 624203,2014
V. A.I. Ansari, M. Hashish,“Effect of abrasive waterjet parameters on volume removal trends in turning”, Journal of engineering for industry, Vol: 117, Pages : 475-484, 1995
VI. F. Kartal , H. Gökkaya, Z.yerlikaya ,”Development of a new method in order to do silent abrasive water jet turning process apparatus”, WJTA-IMCA Conference and Expo, 2015
VII. K. Flogel, F. Faltin, “Waterjet Turning of Titanium Alloys” In Advanced Materials Research, Trans Tech Publications ,Vol: 769, Pages :77-84., 2013
VIII. M. Gupta,S.K. Gill,“Prediction of cutting force in turning of UD-GFRP using mathematical model and simulated annealing” Frontiers of Mechanical Engineering, Vol: 7, Pages : 417-426 ,2012
IX. P Hlaváček, J Cárach,, S Hloch,, K Vasilko, D, Klichová, J. Klich, D. Lehocká,“Sandstone turning by abrasive waterjet”, Rock Mechanics and Rock Engineering, Vol: 48, Pages : 2489-2493, 2015
X. Z. Hutyrová, J. Ščučka, S. Hloch,P. Hlaváček,M. Zeleňák,“Turning of wood plastic composites by water jet and abrasive water jet”, The International Journal of Advanced Manufacturing Technology, Vol: 84,Pages : 1615-1623, (2016)
XI. G. Ramu, B. Bapiraju, M.L. Kumari,“Theoretical and graphical analysis of abrasive water jet turning”, International Journal of Modern Engineering Research, Vol: 3, Pages: 3207-3215, 2013.
XII. F. Kartal, H. Gökkaya, M. Nalbant,“Turning of (Cu-Cr-Zr) alloy with abrasive water jet”, In 21st International Conference on Water Jetting, Ottawa, Canada, (2012, September)
XIII. F. Kartal, M.H. Çetin, H. Gökkaya Z. Yerlikaya,“Optimization of abrasive water jet turning parameters for machining of low density polyethylene material based on experimental design method”, International Polymer Processing, Vol: 29, 535-544, (2014)
XIV. Q.W. Xu, C.H. Qiang, C.W. Guo,“Experimental Study on the Surface Roughness of 1060 Aluminum Alloy Cut by Abrasive Water Jet”, Materials Science Forum, Trans Tech Publications, Vol: 950, Pages: 32-37, 2019
XV. K. Balamurugan,M. Uthayakumar,S. Sankar, U.S Hareesh, K.G.K. Warrier, “Modeling and surface texturing on surface roughness in machining LaPO4–Y2O3 composite”, Materials and Manufacturing Processes, Vol: 33, Pages : 405-413, 2018
XVI. K. Balamurugan, M. Uthayakumar, S.Gowthaman,R. Pandurangan, “A study on the compressive residual stress due to waterjet cavitation peening”, Engineering Failure Analysis, Vol; 92, Pages : 268-277, 2018
XVII. A.C. Bhasha, K.Balamurugan,“Fabrication and property evaluation of Al 6061+ x%(RHA+ TiC) hybrid metal matrix composite”, SN Applied Sciences, Vol: 1(9), Pages : 977, 2019
XVIII. K. Arunkarthikeyan, K. Balamurugan,“Experimental Studies on Deep Cryo Treated plus Tempered Tungsten Carbide Inserts in Turning Operation”, ICAIASM conference proceedings, Santhiram Engineering college, Kurnool, India, 2019