Authors:
Marwah Sami Abboodi,Majid Habeeb Faidh-Allah,DOI NO:
https://doi.org/10.26782/jmcms.2020.04.00008Keywords:
Composite materials,mechanical properties,fatigue life,below knee socket,Abstract
This paper studies the effect of changing layers arrangement of composite materials (four samples consisting of 8 layers with a change in the arrangement of layers and composite materials were used glass fibers, carbon fibers and perlon with lamina matrix) on the mechanical properties (yield stress, ultimate stress, Young's modulus, and Poisson's ratio) of the prosthetic below knee socket (BK) by using tensile test device. Also, calculate the (S-N) curves for these samples by using bending fatigue test device to calculate the fatigue life. The pressure distribution between the (BK)socket and the residual lower limb using pressure sensor and the information on gait cycle was by using force plate on the case study patient with (BK) amputation. The solid work program to drawn the socket and ANSYS workbench 14.5 was used to analyze and evaluate the fatigue characteristic by observing the maximum stress, total deformation and safety factor. The results show that the yield stress in the samples 2, 3 and 4 is increased about 18 %, 95%, and 91% respectively more than the standard sample1. While the ultimate stress in the samples 2, 3 and 4 is increased 32%, 89%, and 68% respectively more than the standard sample1, the Young's modulus in the samples 2, 3 and 4 is increased about 5%, 18%, and 12% respectively more than the standard sample1, the Poisson's ratio is increased about 3%, 6%, and 7% respectively more than the standard sample1, and the fatigue life is increased about 23%, 73% and 29% in the samples 2, 3 and 4 respectively more than the standard sample 1.Refference:
I. A. P. Irawan, I. Wayan S, “Tensile and Impact Strength of Bamboo Fiber Reinforced Epoxy Composite as Alternative Materials for above Prosthetic Socket”, International Conference on Sustainable Technology Development, Vol. 2, pp. 109-115, 2012.
II. A. Adawiya .Hamzah, “Vibrational Behavior of Three Floors Structure Equipped with Dampers”, International Journal of Mechanical and Mechatronics Engineering , Vol.17, No.04, 2017.
III. D .Popovic, T .Sinkjaer, “Control of Movement for the Physically Disabled”, Springer Verlag London, 2000.
IV. H. MajidFaidh-Allah, Mahmood W. Saeed and Adawiya A. Hamzah, “Experimental and Numerical Study the Effect of Materials Changing on Behavior of Dental Bur (Straight Fissure) under Static Stress Analysis” Innovative Systems Design and Engineering , Vol.6, No.2, 2015.
V. H .Majid. Faidh-Allah, Zainab A. Abdul Khalik, “Experimental and Numerical Stress Analysis of Involute Splined Shaft”, Journal of Engineering, College of Engineering, University of Baghdad, Vol.18 , No.4 , 2012.
VI. H. SaleelAbood, Majid H. Faidh-Allah, “Analysis of Prosthetic Running Plate of Limb Using Different Composite Materials”, Journal of Engineering, College of Engineering, University of Baghdad, Vol.25, No.12, pp.15-25, 2019.
VII. H. Majid .Faidh-Allah, Adawiya A. Hamzah, “Vibration Analysis of Aircraft Wing under Gust Load”, Journal of Engineering and Applied Sciences, Vol.14, No.11, pp.3571-3574, 2019.
VIII. H. Majid .Faidh-Allah, “Study the Steady-State and Dynamic Problems of the Rotating Blades”, International Journal of Mechanical Engineering and Technology, Vol.9, No.10, pp.548-558, 2018.
IX. H. Majid .Faidh-Allah, “The Temperature Distribution in Friction Clutch Disc under Successive Engagements”, Tribology in Industry, Vol.40, No.1, pp.92-99, 2018.
X. Hamill, J. and Knutzen, K., “Biomechanical Basis of Human Movement”, 2nd edition, Philadelphia: Lippincott Williams & Wilkins, 2003.
XI. K Sethi, P., “Technological Choices in Prosthetics and Orthotics for Developing Countries”, Prosthetic and Orthotics International ,Vol.13, pp.117-124,1989.
XII. Karen Junius, TomVerstraten, “Design of an Actuated Orthosis for Support of the Sound Leg of TransfemoralDysvascular Amputees”, Master Thesis in Department of Mechanical Engineering Vrije Universities Brussel Academic year: 2011 – 2012.
XIII. M. J. Jweeg , S. S. Hasan and J. S. Chiad , “Effects of Lamination Layers on the Mechanical Properties for above Knee Prosthetic Socket”, Eng. & Tech. Journal,Vol.27, No.4, 2009.
XIV. M .MuhammedA., “Experimental Investigation of Tensile and Fatigue Stresses for Orthotic / Prosthetic Composite Materials with Varying Fiber (Perlon, E-Glass and Carbon)”. Arpn Journal of Engineering and Applied Sciences, vol. 11, no. 21, November 2016.
XV. Standard, A. S. T. M. (2003), “Standard Test Method for Tensile Properties of Plastics”, ASTM International. Designation: D, 638, 1-13.
XVI. T. Mustafa Ismail ,Muhsin J. Jweeg and Kadhim K. Resan, “Study of Creep- Fatigue Interaction in the Prosthetic Socket below Knee”, Innovative Systems Design and Engineering , Vol.4, No.5, 2013.